Defender LED rear number plate light licence plate lamp 12 & 24V E approved (407LEDRLPL) In Stock, Available for Same Day Dispatch

£16.80
£14.00 ex. VAT

Qty:
Add To Wishlist

Description

LED numper plate lamp from a Land Rover OE supplier.

Direct replacement for the original item, although a new hole will need to be drilled through the plinth to route the wires - this will not be visible once re fitted.

Tools required

  • Screwdriver
  • 8mm socket & ratchet
  • Wire cutters
  • Crimpers
  • Hot air gun / gas lighter

Step 1 - Original light!

Step 2 - Remove the fixing screw holding the lamp cover on

Step 3 - Cover removed bulb holder exposed

Step 4 - Remove bolts using 8mm socket or spanner

Step 5 - Remove mounting plinth from body work

Step 6 - Remove M5 bolts and retain for replacement LED unit. Cut wires to existing lamp leaving long enough tails to rejoin later.

Step 7 - Note marks left when plinth moulded these can be used as a rough guide when drilling.

Step 8 - Using a suitable sized drill bit (I used a step drill) make a clearance hole big enough to pass the cables from the LED unit through the plinth and enable the lamp to sit flush without the cables being pinched or trapped.

Step 9 - Pass through cable from LED unit

Step 10 - Remove fixing screw from cover on LED unit

Step 11 - Remove black plastic cover exposing internal lamp - note square holes where the existing bolts will pass through..

Step 12 - Take an M5 washer and place over original fixing bolt and re insert in to lamp there was enough tension to hold the bolts in to do the next step.

Step 13 - Strip back wires and insert into heat shrink butt connectors

Step 14 - Crimp connectors up

Step 15 - Gently warm the crimp and it will shrink down, continue warming and you will notice the glue melt and fill the void inside the crimp.

You are now finished so stop heating!

Step 16 - Carefully arrange the wires into the void under the plinth

Step 17 - Refit light & plinth to the body and tighten bolts.

Step 18 - Refit new black plastic cover

Step 19 - Test the light!

 

 

You May Also Like

12N 7 pin black in line plastic socket 12 Volt

Out of Stock
Back ordered products can take up to 8 weeks to arrive

£5.59
£4.66 ex. VAT

View

12N 7 pin black plastic plug 12 Volt

Out of Stock
Back ordered products can take up to 8 weeks to arrive

£1.91
£1.59 ex. VAT

View

12N 7 pin black plastic socket 12 Volt

Out of Stock
Back ordered products can take up to 8 weeks to arrive

£1.92
£1.60 ex. VAT

View

Amber Hyper Brite Trio light head

Out of Stock
Back ordered products can take up to 8 weeks to arrive

£138.00 £137.94
£114.95 ex. VAT

View

Amber LED Trio light kit with 7 flash patterns

Out of Stock
Back ordered products can take up to 8 weeks to arrive

£120.00
£100.00 ex. VAT

View

CTEK comfort connector to 12S plug charging adaptor for charging vehicle battery through towing socket

In Stock, Available for Same Day Dispatch

£24.00 £23.94
£19.95 ex. VAT

View

CTEK comfort connector to 13 pin plug charging adaptor for charging vehicle battery through towing socket

In Stock, Available for Same Day Dispatch

£24.00 £23.94
£19.95 ex. VAT

View

Deutsch DT series protective cable over boot cover DT2S-BT-BK to suit 2 way DT06 2S

In Stock, Available for Same Day Dispatch

£0.76
£0.63 ex. VAT

View

Recently Viewed

Featured Brands

KlaukePro CarVTE IncAMP Tyco TE ConnectivityAntilaserBlue Sea SystemsCarling TechnologiesCTEKDelphi PackardDeutschFTZJ W SpeakerLabcraftLED AutolampsLittelfuse / MenbersMagcodeMobile CentrePower ProbeSealed Bus BarSho Me / Able 2 ProductsSutarsTesa